Page 1 of 1

P3D v4.1 Tweaking

PostPosted: Sat Oct 21, 2017 7:31 am
by LCYCowboy
Hello All,

I know that there is a FlyInside Wiki page, but I have recently got back into flying P3D (after a while solely on DCS) and having spent days installing the latest versions (thanks for v4 Dan) I have it running.

In v3 I was always getting about 40-50/90 fps with FI. After installing v4 and setting it up with similar settings, I was getting 30/90 and 20/90 with the PMDG DC-6. Turning down the Super Sampling in FI didn't help much.

I did a lot of trawling, and found a few threads (non vR) on AVSIM. I now have the sim running at about 50/90 with the A2A Comanche and 35-40/90 with the DC-6. I am aware that I may still be missing something, so was hoping that we could set up some kind of thread which shares all of the tips people have found to smooth things out. I know everyone has different hardware, but there must be some settings which really help everyone.

For my part, I did the following:

Change ASCA cloud textures to 512x512. This had a big impact, and as the VR resolution is quite bad anyway, makes little or no difference to what you see.

Anisotropic Filtering can stay at 16 without any noticeable difference.

I run VSync off and leave target FPS at unlimited (is this the best setting for VR)

One thread mentioned leaving Mesh res at 19m and Texture res at 60cm, as anything above isn't all that noticeable, and it helps.

Here are my settings:

p3d 1.jpg
p3d 1.jpg (51.42 KiB) Viewed 8046 times


p3D 2.jpg
p3D 2.jpg (49.1 KiB) Viewed 8046 times


p3d 3.jpg
p3d 3.jpg (37.82 KiB) Viewed 8046 times




Can anyone see anything glaring which would help?

I know traffic is a killer, but I just love the immersion of cars whizzing along as I come in to land.

Thanks

Neil

Re: P3D v4.1 Tweaking

PostPosted: Sun Oct 22, 2017 9:21 am
by malexdu
Great idea LCYCowboy,

I stand to be corrected... but I think Flyinside will not run with vsync enabled, however it may be linked to what monitor your using. I have played around with the target frame rate, results vary considerably subject to where your flying, but I have found setting it to unlimited gives me the best results as well. In terms of frame rates...I have found shadows can have a big hit, I turn clouds, buildings and terrain cast shadows to off. On my system this can give me a 2-7 FPS boost.

For me VR is the only way to go, but there is a price to pay...and that is in graphics. Any advice to help make the graphics a little clearer and easier to read is a winner for me, especially AA and texture filtering settings. Also advice on Nvidia settings could be useful as well.

Regards

Re: P3D v4.1 Tweaking

PostPosted: Sun Oct 22, 2017 9:52 am
by Tony
Good idea I'll make this a sticky ;)

Re: P3D v4.1 Tweaking

PostPosted: Wed Nov 01, 2017 4:06 am
by FlyingMonkey
I'm curious about the option "mipmap VC panels": why did you choose to turn it off? It is supposed to improve the clarity of instruments a lot. Is it because it doesn't work well in VR or is too taxing? I had it on by default and didn't even notice that option until now.

Re: P3D v4.1 Tweaking

PostPosted: Sun Mar 04, 2018 9:39 am
by malexdu
I know Flyinside does not support SSAA and if set it will ask to change this on start up. Once FI is running go to the P3D menu and change AA to 2 x SSAA. The improvement in simmer is very noticeable and impact on performance not a killer. If you use 4 x SSAA this is even better, but in areas with lots of addons such as London with Orbx scenery etc. it does have an impact on frame rates.

Question ....why does FI not allow SSAA?

Re: P3D v4.1 Tweaking

PostPosted: Sat Jun 09, 2018 4:11 am
by markwrd1
Just what i wanted to read this morning! I have just set up my rift and I was playing around with the 15 minute flights last night. The immersion is incredible. resolution is poor but I expected that and was fully aware. I, however, have the same issue. I used to hold a solid 50fps on my 47" TV but im now hitting a tremendous 15-20fps in the headset. I'll give this a blast tonight and hopefully see some perfomance increases. Great idea for a tweaking thread

Re: P3D v4.1 Tweaking

PostPosted: Mon Oct 15, 2018 10:17 am
by severniae
Was there a general consensus on what are the best tweaks for v4?

A lot of discussion here has died of late :(